The Bambu Lab AMS (Automatic Material System) makes multicolor printing feel almost magical: you load up to four spools per unit and the printer swaps between them on its own. The tradeoff is waste. Every color change has to clear the old color out of the nozzle, and on a print with many changes, that purged plastic can add up to more than the model itself. This guide explains what is happening and how to keep waste under control.
How a color change works
A single-nozzle printer with an AMS can only push one filament at a time. At each color change, the printer:
- Cuts the current filament with a built-in cutter near the toolhead.
- Retracts it back to the AMS.
- Feeds the next filament down to the hotend.
- Purges (flushes) plastic through the nozzle until the old color is gone.
- Resumes printing.
On most Bambu printers, the purge comes out of the nozzle near the back of the machine and is flung down the chute as the familiar "poop." Each swap takes time, often somewhere around 30 seconds to a minute or more, depending on the printer and purge volume. A model with hundreds of color changes can spend hours swapping.
Flush volumes
The flush volume is how much plastic the printer pushes through the nozzle to clear the previous color. Bambu Studio and OrcaSlicer show it as a matrix: for each pair of colors (from one filament to another), there is a separate value in cubic millimeters.
Why does it vary by pair? Because some transitions are much harder than others:
- Dark to light (black to white, red to yellow) needs the most purge, since even a little leftover dark pigment tints a light color.
- Light to dark (white to black) needs much less, because dark colors hide traces of the previous color.
- Similar colors (two shades of blue) need very little.
Bambu Studio estimates these values automatically from the filament colors. You can open the flushing volume dialog from the filament area of the Prepare tab and adjust the multiplier or individual values.
Practical flush settings
- Start with the automatic values. They are conservative and usually clean.
- If you see no color contamination, try lowering the multiplier gradually, for example from 1.0 to 0.8, and print a test.
- For transitions into white or other very light colors, keep values high. Contamination is most visible there.
- If you see streaks of the old color at the start of a new color, increase the flush volume for that specific pair.
Prime towers
The prime tower is a small block printed beside your model. After each color change, the printer prints a little on the tower before returning to the model. It serves a few purposes:
- It stabilizes pressure in the nozzle so the first lines on the model are clean.
- It catches any remaining color bleed that the purge did not clear.
- It gives the printer a place to wipe off oozing plastic.
You can disable the prime tower in some cases, but for most multicolor prints it noticeably improves quality. Keep it close to the model but not touching it, and make sure the tower is wide enough to stay stable on tall prints. In Bambu Studio and OrcaSlicer you can adjust the tower width and position in the plate view.
Flushing into infill or objects
Bambu Studio and OrcaSlicer can send some of the purge into parts of the print where color does not matter:
- Flush into objects' infill. The transition plastic becomes part of the model's internal infill instead of being discarded. This works well on models with substantial infill.
- Flush into objects' support. Similar, but uses support material.
- Flush into this object. Lets you mark an entire object, such as a small hidden piece or a test part, as a purge target.
These options can reduce waste significantly, but they are not free. Infill only absorbs so much plastic per layer, and on thin or small models there is not much room. Check the preview to see how much is actually being absorbed.
Tips to reduce waste
The biggest savings come from how a model is designed and set up, not just from slicer tweaks.
- Print multiple copies at once. Waste comes per color change, per layer. If you print four copies on the same plate, each layer still needs roughly the same number of swaps, so the waste per copy drops a lot.
- Reduce the number of color changes per layer. Models that change color only at certain heights (for example, a white base and a red top) need far fewer swaps than models with colors mixed on every layer.
- Order colors sensibly. Slicers usually optimize the order of filaments within each layer. Grouping light colors first and darker colors later helps keep flush volumes low.
- Use lighter colors where possible. If a design is flexible, avoid lots of transitions from dark colors into white.
- Use larger layer heights where detail allows. Fewer layers means fewer color changes overall. Going from 0.12 mm to 0.2 mm layers can cut swaps substantially.
- Consider color by height. For simple designs like signs or keychains, printing color changes at specific layers can produce a great result with very little waste.
- Save the purge. Some makers collect purge waste to send to recycling programs or use it as small craft material.
Why our multicolor 3MF files help
Our multicolor 3MF files come with colors already assigned and arranged with waste in mind. Where possible, we design models so that colors change by layer height or are grouped to minimize swaps. When a model genuinely needs lots of changes for its look, our product page notes it, so you can decide whether to print it in full color or as separate parts.
You can also print most multicolor models as separate single-color parts and assemble them afterward. That approach uses almost no purge, at the cost of some assembly time.
Summary
- Each color change cuts, retracts, loads, and purges, which costs time and plastic.
- Flush volumes depend on the color pair, with dark-to-light transitions needing the most.
- Prime towers improve quality after swaps.
- Flushing into infill and printing multiple copies are the easiest ways to reduce waste.
- Designs with fewer swaps per layer are the most efficient of all.